Re: Re: DDAR, ARF ARF 2...[Answer]

["Andy Powell" <ukha@xxxxxxx>]

I'll upload it to the files area...

Andy

*********** REPLY SEPARATOR  ***********

On 24/08/01 at 18:15 Shmern wrote:

>Ok I've done MOST of this, BUT I can't find a dos tar.exe to compress
them
>again, Anyone help ?
>
>D.
>----- Original Message -----
>From: "Shmern" <shmern@xxxxxxx>
>To: <ukha_d@xxxxxxx>
>Sent: Friday, August 24, 2001 5:46 PM
>Subject: Re: [ukha_d] Re: DDAR, ARF ARF 2...[Answer]
>
>
>> Can someone post a modified version of receiver.arf ?
>>
>> so we all don't have too do this ??
>>
>> D.
>> ----- Original Message -----
>> From: "Justin" <justin@xxxxxxx>
>> To: <ukha_d@xxxxxxx>
>> Sent: Friday, August 24, 2001 5:20 PM
>> Subject: Re: [ukha_d] Re: DDAR, ARF ARF 2...[Answer]
>>
>>
>> > Andy,
>> > how do you get around the DOS naming issue when re-tarring?
>> > Justin
>> >
>> > ----- Original Message -----
>> > From: Andy Powell <ukha@xxxxxxx>
>> > To: <ukha_d@xxxxxxx>
>> > Sent: Friday, August 24, 2001 2:22 PM
>> > Subject: [ukha_d] Re: DDAR, ARF ARF 2...[Answer]
>> >
>> >
>> > > Ok,
>> > >
>> > > so no one knew or cares :-( ... but I think I've managed
it (although
>> > > can't test the final result just yet.. anyhow here are
the steps I've
>> > > performed so far:
>> > >
>> > > Tools needed: WinRAR, tar (msdos)
>> > >
>> > > 1. Use WinRAR un uncompress the receiver.diff.arf.gz
file
>> > > 2. Rename the resultant receiver.diff.arf file to
receiver.diff.TAR
>> > > 3. Use WinRAR to uncompress the receiver.diff.TAR file
>> > > 4. Backup (DO THIS PLEASE!!!) the receiver.arf file from
the DELL
>> > > Audio Receiver directory
>> > > 5. Rename the receiver.arf file to receiver.TAR
>> > > 6. Use WinRAR to uncompress the receiver.diff.TAR file
>> > > 7. Copy the files and direcotries from step 3 to where
the files from
>> > > step 6 are.
>> > > 8. Use TAR to recompress the files/dirs into a new
archive .eg.
>> > > myreceiver.TAR
>> > > 9. Rename the myreceiver.TAR file to receiver.arf
>> > >
>> > > [these folloing steps have not yet been performed by me
(waiting for
>> > > DDAR arrival)
>> > >
>> > > 10. Reboot the DDAR.
>> > > 11. Pray
>> > > 12. If all goes well then use:
>> > >
>> > > http://<ip-address of receiver>/receiver.html
>> > >
>> > > from your PC and you should be able to control and view
your DDAR
>> > > remotely. Use Terminal services and you could run it on
your
>> > > EPODS/Ipaq etc :-)))
>> > >
>> > > 13. If any problems occur after DDAR reboot you can
replace the newly
>> > > created receiver.arf file with the original backed up
version.
>> > >
>> > >
>> > > Andy
>> > >
>> > > --- In ukha_d@y..., "Andy Powell"
<ukha@b...> wrote:
>> > > >
>> > > > Ok,
>> > > >
>> > > > has anyone (under windows) installed the
displayserver hack? I've
>> > > > read what little instructions there are and...well
- I haven't got
>> > > a
>> > > > clue.... has somone (using Linux) built the
appropriate .arf file??
>> > > >
>> > > > below is the text from the readme - as you can see
it assumes a
>> > > lot -
>> > > > like you know what he's talking about for a start!
>> > > >
>> > > > "This is displayserver for the rio receiver.
>> > > > unzip the receiver.diff.arf.tgz file and add the
files to the
>> > > > original receiver.arf file. Do not use winzip to do
this; device-
>> > > > files contained in the arf file will be lost...
>> > > > after installation open your webbrowser and point
it to :
>> > > > http://<ip-address of receiver>/receiver.html
>> > > > Enjoy..."
>> > > >
>> > > > Andy
>> > >
>> > >
>> > >
>> > > For more information: http://www.automatedhome.co.uk
>> > > Post message: ukha_d@xxxxxxx
>> > > Subscribe:  ukha_d-subscribe@xxxxxxx
>> > > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
>> > > List owner:  ukha_d-owner@xxxxxxx
>> > >
>> > > Your use of Yahoo! Groups is subject to
>> http://docs.yahoo.com/info/terms/
>> > >
>> > >
>> > >
>> >
>> >
>> >
>> >
>> > For more information: http://www.automatedhome.co.uk
>> > Post message: ukha_d@xxxxxxx
>> > Subscribe:  ukha_d-subscribe@xxxxxxx
>> > Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
>> > List owner:  ukha_d-owner@xxxxxxx
>> >
>> > Your use of Yahoo! Groups is subject to
>http://docs.yahoo.com/info/terms/
>> >
>> >
>>
>>
>>
>> For more information: http://www.automatedhome.co.uk
>> Post message: ukha_d@xxxxxxx
>> Subscribe:  ukha_d-subscribe@xxxxxxx
>> Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
>> List owner:  ukha_d-owner@xxxxxxx
>>
>> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>>
>>
>
>
>
>For more information: http://www.automatedhome.co.uk
>Post message: ukha_d@xxxxxxx
>Subscribe:  ukha_d-subscribe@xxxxxxx
>Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
>List owner:  ukha_d-owner@xxxxxxx
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/


--- Tag-it! v2.0 (c) Andy Powell ,1998,1999,2000...and beyond..