The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Mounting kit...


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Is this safe for running Power and cat 5?


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Is this safe for running Power and cat 5?
  • From: "Brian G. Reynolds" <brian.g.reynolds@xxxxxxx>
  • Date: Thu, 20 Dec 2001 22:43:22 -0000
  • Delivered-to: mailing list ukha_d@xxxxxxx
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Err, what is/are "catineries"?
 
B.
-----Original Message-----
From: simon rafferty [mailto:musashi1977uk@xxxxxxx]
Sent: 20 December 2001 22:40
To: ukha_d@xxxxxxxSubject: Re: [ukha_d] Is this safe for running Power and cat 5?

Personally if you are going above ground why noy just string to catineries, one for power and one for data. Make sure that the power cable is external grade (like screwfixes 3 core FROST CABLE which is frost and UV protected , do not run normal T&E as the sheathing is not UV protected and will degrade. As for the CAT5 again most of this stuff is not external grade and will degrade. You can get external grade CAT5 cable but it is quite expensive. Better to run several strands inside some commercial hosepipe (the yellow or black stuff, not the green transparent stuff) and clip this to the catinery. Alternatively if you are going underground i would run 2 lots of 2 1/2 inch waste pipe (with the joints cement welded) one for power and one for Data with a pulling tape left permanantly installed in both incase you need to pull cables in future.

Simon Rafferty

  Mick Furlong <dorsai@xxxxxxx> wrote:

Hi all

I have a need to run power and Cat 5 to a speperate garage. I was intending
to run this underground but then thought of what may be an easier method but
I am not sure it is safe.

Idea is to build a hollow beam out of wood...say 4 lengths of 4x1 giving a
6x4 beam...with a 4x2 hollow down the centre and to either run power down
one side , data down the other either with or without some kind of
seperator.

Questions are first would this be safe (beam would be at 8ft level)assuming
it is all properly weather protected. Second would the seperation between
cat 5 and the power be enough or would I need to bulid in some kind of
shielding?

thanks in advance

Mick



For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.



Do You Yahoo!?
Get personalised at My Yahoo!.

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.