The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Re: Confused by Current Cost


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Re: Splitting composite video


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Re: Splitting composite video
  • From: "Keith Doxey" <ukha@xxxxxxx>
  • Date: Wed, 21 May 2003 19:33:33 +0100
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Not quite, they are dual op-amps so will do two circuits.

Single Op Amp

nc	1	8	nc
-in	2	7	+ve
+in	3	6	out
-ve	4	5	nc

Dual op amp

out1	1	8	+ve
-in1	2	7	out2
+in1	3	6	-in2
-ve	4	5	+in2

Make sure you fit a 0.1uF ceramic capacitor from each power supply pin ( 4
&
8) to ground as close as possible to the opamp


Keith

www.diyha.co.uk
www.kat5.tv


> -----Original Message-----
> From: Paul [mailto:groups@xxxxxxx]
> Sent: 21 May 2003 14:56
> To: ukha_d@xxxxxxx
> Subject: RE: [ukha_d] Re: Splitting composite video
>
>
> Thanks Keith, would they drop straight into the circuit as a
> direct replacement I mentioned at:
>
>
>
> http://home.maine.rr.com/randylinscott/jan98.htm
>
>
>
> ?
>
>
>
> Ta,
>
>
>
> Paul.
>
>
>
> P.S. still editting your video!
>
>
>
> -----Original Message-----
> From: Keith Doxey [mailto:ukha@xxxxxxx]
> Sent: 21 May 2003 14:49
> To: ukha_d@xxxxxxx
> Subject: [ukha_d] Re: Splitting composite video
>
>
>
> Analog Devices AD828
> Elantec EL2244
>
> Both Dual Opamps capable of video. Used hundred of them :-)
>
> Keith
>
>
> --- In ukha_d@xxxxxxx, "Paul" <groups@s...> wrote:
> > Oh, and I found out the op amp used in the circuit (CA3100) is
> obsolete so I'm at a bit of a loss now :-(
> >
> >
> >
> > Help!... Keith??? Stuart??? Frank or any other electronics gurus?
> >
> >
> >
> > Paul.
> >
> > -----Original Message-----
> > From: Paul [mailto:groups@xxxxxxx...]
> > Sent: 21 May 2003 14:07
> > To: ukha_d@xxxxxxx
> > Subject: RE: [ukha_d] Splitting composite video
> >
> >
> >
> > I've had a look at a few of the circuits on the page Stuart sent
> me. I like the look of the following:
> >
> >
> >
> > http://home.maine.rr.com/randylinscott/jan98.htm
> >
> >
> >
> > Any thoughts on this as there isn't much detail around it i.e.
any
> particular precautions if I'm going to make it (shielding, layout,
> component specs etc). I would make up 5 of the circuits on a
> veroboard).
>
>
>
>
>
>
>
> Yahoo! Groups Sponsor
>
>
>
> <http://rd.yahoo.com/M=251812.3170658.4537139.1261774/D=egroup
> web/S=1705041992:HM/A=1564415/R=0/*http:/www.netflix.com/Defau
> lt?mqso=60164784&partid=3170658>
>
>
>
> <http://us.adserver.yahoo.com/l?M=251812.3170658.4537139.12617
74/D=egroupmail/S=:HM/A=1564415/rand=787182471>


** UKHA2004 BE THERE! ** - start planning now.

http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/>
 Terms of Service.



[Non-text portions of this message have been removed]



** UKHA2004 BE THERE! ** - start planning now.

http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/



[Non-text portions of this message have been removed]



Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.