Re: [OT] Asterisk at home help + XAP integration

["Chris Purves" <CHRIS_PURVES@xxxxxxx>]

Will do - thanks Paul.

Chris

--- In ukha_d@xxxxxxx, "Paul Gale" <groups@s...> wrote:
>
> TBH the SPA3000 config was a nightmare to get working! I'm not using
Sipgate.
>=20
> I don't have time ATM to output the configs but if you email me when
you get your SPA3000, I'll email them over to you.
>=20
> Paul.
>=20
>=20
>=20
> > -----Original Message-----
> > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On
Behalf Of
> > Chris Purves
> > Sent: 19 October 2005 11:37
> > To: ukha_d@xxxxxxx
> > Subject: [ukha_d] Re: [OT] Asterisk at home help + XAP
integration
> >=20
> > Paul - any chance of a copy of your config files ? I have not
even
> > gone near that aspect yet but have printed a ton of stuff from
the net
> > that might help me. You're not using sipgate by any chance are
you ?
> >=20
> > I always struggle to understand the difference between xap and
xpl. I
> > have only used xap so far (with CBUS via the CBUS/XAP gateway).
> >=20
> > I have 3 touchpanels around the house so I am keen to get
integrating
> > when support arrives.
> >=20
> > Ta
> > Chris
> >=20
> > --- In ukha_d@xxxxxxx, "Paul Gale" <groups@s...>
wrote:
> > >
> > > xAP support for Asterisk is still being worked on but I've
not heard
> > anything for a couple of weeks. Should be good though - I've
asked for
> > message waiting support which would allow good integration into
my HA
> > network.
> > >
> > > I have the same config as you - Dell server, *@H, SPA3000 -
works
> > really well.
> > >
> > > Paul.
> > >
> > > > -----Original Message-----
> > > > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On
> > Behalf Of
> > > > Ian Lowe
> > > > Sent: 19 October 2005 11:01
> > > > To: ukha_d@xxxxxxx
> > > > Subject: RE: [ukha_d] [OT] Asterisk at home help + XAP
integration
> > > >
> > > > Asterisk at Home has xPL built in, not xAP.
> > > >
> > > > If you have xAP bits and bobs already, I think there's
a xAP
> > module for
> > > > Asterisk (not quite sure about the mechanics of AAH vs
Asterisk
> > raw there)
> > > > -
> > > > I'm sure Patrick or Kevin mentioned that previously?
> > > >
> > > > If you don't have an existing set of tools, have a look
at xPL.
> > (there's a
> > > > yahoo group over here: ukha_xpl@xxxxxxx )
> > > >
> > > > Ian.
> > > >
> > > > -----Original Message-----
> > > > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On
> > Behalf Of
> > > > christopher purves
> > > > Sent: 19 October 2005 10:43
> > > > To: ukha_d@xxxxxxx
> > > > Subject: [ukha_d] [OT] Asterisk at home help + XAP
integration
> > > >
> > > > Hi All,
> > > >
> > > > Well I have finally installed *@home and as I know
quite a few of
> > you use
> > > > it
> > > > I wanted comments on my master plan before I set out to
check
I'm not
> > > > being
> > > > an idiot.
> > > >
> > > > I have installed *@Home on a Dell =A399 server (TM) and
that all
> > seems fine
> > > > -
> > > > painless install.
> > > >
> > > > I propose the following - use Linksys PAB2 adapters on
all fixed
> > analogue
> > > > phones in the house. Buy a sipura 3000 to connect in
the POTS land
> > line
> > > > and
> > > > to plug an 'emergency' phone into - on a power fail a
relay in the
> > sipura
> > > > bridges the FXO and FXS ports so I can still use the
emergency
> > phone no
> > > > matter what.
> > > >
> > > > I have a couple of sipgate numbers now - I was gonna
use one for
> > voice and
> > > > one for fax and route appropriately.
> > > >
> > > > I think I simply need to enable XAP in the * config to
get XAP
> > messages ?
> > > >
> > > > Does that make some kinda sense?
> > > >
> > > > Ta
> > > > Chris
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> >=20
> > Yahoo! Groups Links
> >=20
> >=20
> >=20
> >=20
> >=20
> >
>