Re: Re: Simple Multi Room Audio help

["Tim Hawes" <timsyahoo@xxxxxxxxxxxxxx>]

I had anthoer thought last night - there's also these little amps
which get excellent reviews:
http://www.tnt-audio.com/ampli/t-amp_e.html

They're small in size and can run from batteries if needed, or from
mains (adaptor?). They were going for very little money but I haven't
seen too much discussion of them recently.

HTH,

Tim.

On 2/8/07, Tim Hawes <timsyahoo@xxxxxxx> wrote:
> Hi Simon,
>
> Re: mounting outside, it was just that you said your bathroom was
> fully tiled and you wanted to remove the system later.
>
> IIRC CPC also did volume controls with an "off" position,
although I
> can't remember whether they were for 100V 'PA' type applications or
> for standard home hifi speakers...
>
> CPC sell (can you tell I'm a fan? ;-)  ) speaker switch boxes, as do
> maplin etc. so no, switching off one set of speakers shouldn't
> *damage* the amp. It may change the volume for the other pair speakers
> still operating though, depending on how your amp is configured.
>
> HTH, and be sure to post some pics when you're done :-)
>
> Tim
>
> On 2/8/07, seniorsimon <simon.ryley@xxxxxxx> wrote:
> > Hi Tim,
> >
> > Thats just the kind of info I was after, it does seem that a
speaker
> > level volume control makes more sense.
> >  http://tinyurl.com/yr78gd looks fine
for what I need and the price is =
ok.
> >
> > Is there any particular reason you would mount the speaker
control
> > outside the bathroom door?
> >
> > The only bit I need to fathom now is whether turning the volume
down
> > to minimum will completely mute the sound or whether I need some
kind
> > of switch to disconnect the speakers from the source.  Will
> > disconnecting the speakers from the source using a switch damage
the am=
p?
> >
> > This is my first real audio project so I'm learning as I go.
> >
> > Thanks everyone for the help so far.
> >
> > Simon
> >
> >
> >
> > --- In ukha_d@xxxxxxx, "Tim Hawes"
<timsyahoo@...> wrote:
> > >
> > > Hi Simon,
> > >
> > > I assume that the volume control circuit in your original
link goes
> > > between your source (CD, tape, FM etc) and the amplifier as
it doesn'=
t
> > > appear to be a "speaker level" unit. That's ok,
but it does force you
> > > into a separate amp and sources, rather than an integrated
amplifier.
> > >
> > > CPC have some "speaker level" volume controls, as
do Lets Automate
> > (IIRC).
> > > I might be tempted to mount these just outside the bathroom
door,
> > > rather than inside though. Shout if you can't find them and
I'll dig
> > > out some part numbers.
> > >
> > > Your local Freecycle group should be able to come up with an
amplifie=
r
> > > - there's always some on the Guildford group :-)
> > >
> > > You don't have to take the power feed from the bathroom
rose, you
> > > could use any convenient supply, or if your bathrooms are
downstairs,
> > > add a fused spur from the upstairs ring main :-)
> > >
> > > HTH,
> > >
> > > Tim.
> > >
> > > On 2/7/07, Simon Ryley <simon.ryley@...> wrote:
> > > > Thanks Tim.
> > > >
> > > > As my bathroom has downlighters, I don't have a rose to
take the po=
wer
> > > > from.  (I've just checked; the neutral is in the wall
light switch
> > > > outside the bathroom and getting to that switch without
hacking
> > the wall
> > > > apart is going to be tricky)
> > > >
> > > > They do look like a good product, but will be =A3200+
for both
> > bathrooms,
> > > > which seems a tad steep.
> > > >
> > > > Does anyone know if my original plan will be cheaper,
otherwise I'l=
l
> > > > start saving...
> > > >
> > > > Simon
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Tim Hawes wrote:
> > > > >
> > > > > You can take power from the permanent live from a
ceiling rose (i=
.e.
> > > > > the light bulb itself would be on the switched
live side).
> > > > >
> > > > > IMHO the ceiling void is not part of the bathroom,
and you don't
> > > > > *need* to take the power from the bathroom ceiling
rose anyway.
> > Part P
> > > > > lets you modify existing circuits - some of the
major exclusions =
are
> > > > > adding completely new circuits from the consumer
unit and wiring
> > > > > *inside* kitchens & bathrooms. Extending an
existing lighting
> > circuit
> > > > > to include this unit would fall outside Part P
IMHO, but I'm just=
a
> > > > > home owner...
> > > > >
> > > > > It looks a pretty good product :-)
> > > > >
> > > > > HTH,
> > > > >
> > > > > Tim.
> > > > >
> > > > > On 2/7/07, Simon Ryley <simon.ryley@...
> > > > > <mailto:simon.ryley%40orange.net>>
wrote:
> > > > > > Hi Stuart,
> > > > > >
> > > > > > I did see those in my googling around the
subject and they look
> > > > > pretty good.
> > > > > >
> > > > > > My only concern was how to provide power?
> > > > > >
> > > > > > I would guess they can't be powered from the
lighting circuit
> > so would
> > > > > > need a fused connection unit fitting outside
the bathroom
> > spurred from
> > > > > > the nearest wall socket, which I think gets
me nicely into the
> > realms of
> > > > > > Part P and needing to get a sparky in?
> > > > > >
> > > > > > How are yours wired up?
> > > > > >
> > > > > > Thanks,
> > > > > >
> > > > > > Simon
>