Re: HV Macro runs multiple times

["gmotichka" <gmotichka@xxxxxxxxxxxxx>]

Thanks

I'm excited about how far Ive come. It will be very usefull once tht
roadblock it overcome.Then I will need to determine how much to
program into xPl and how much to leave at the HV level.

George




--- In ukha_xpl@xxxxxxx, "Frank Mc Alinden" <fmcalind@b...>
wrote:
> Hi George
>                 I think Mal (the w800 developer) might need to
have a look
> at the app.....
>
> Just hang in there it will be sorted soon........
>
> Frank
>
>
> ----- Original Message -----
> From: "gmotichka" <gmotichka@h...>
> To: <ukha_xpl@xxxxxxx>
> Sent: Sunday, December 05, 2004 6:43 AM
> Subject: [ukha_xpl] Re: HV Macro runs multiple times
>
>
> >
> >
> > Yes, Tried as quick as possible on the press -- no difference.
Then
> > I thought maybe because on the conditions I had "*" for
target,
so I
> > tried using just "GSHED-HVISION", but then it did not
get passed
to
> > HV to process.
> >
> > George
> >
> >
> >
> >
> >
> > In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
<fmcalind@b...>
> > wrote:
> > > Hi George
> > >
> > > > Yes, I get multiple messages in the xPL monitor. It
usually
> > shows 3
> > > > instances - yet the macro executes up to 6 times.
> > >
> > > If its receiving multiple copies of the same command each
time
a
> > button is
> > > pressed , a delay may be required to filter out  some of the
> > repeated
> > > commands....I think Mal would need to have a look at
this.....
> > >
> > > I assume you have tried very short presses and still get
multiple
> > received
> > > w800 messages ??
> > >
> > > Frank
> > >
> > > ----- Original Message -----
> > > From: "gmotichka" <gmotichka@h...>
> > > To: <ukha_xpl@xxxxxxx>
> > > Sent: Sunday, December 05, 2004 6:25 AM
> > > Subject: [ukha_xpl] Re: HV Macro runs multiple times
> > >
> > >
> > > >
> > > >
> > > > Yes, I get multiple messages in the xPL monitor. It
usually
> > shows 3
> > > > instances - yet the macro executes up to 6 times.
> > > >
> > > > George
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > --- In ukha_xpl@xxxxxxx, "Frank Mc Alinden"
> > <fmcalind@b...>
> > > > wrote:
> > > > > > I am getting very close on this working. I
now have it
where
> > the
> > > > x10
> > > > > > signal is recognized by the W800 and then
triggers the
macro
> > in
> > > > > > HomeVision.
> > > > >
> > > > > Good news.......
> > > > >
> > > > > > The problem is that it will execute the macro
multiple
> > times --
> > > > > > anywhere from 3 to 6 times consecutively. I
can see the
> > multiple
> > > > > > commands going to HV. I tried to add a 'macro
disable"
> > command in
> > > > > > the macro, but that did not help. Neither did
adjusting
the
> > > > ddespeed
> > > > > > or lastsent options in the configuration
> > > > >
> > > > > Are you receiving multiple message in xPL Monitor
?? when
you
> > > > press a button
> > > > > on your rf remote ???......If so The w800-app
might
require a
> > > > built in delay
> > > > > ....Hopefully Mal will post regarding the
app.......
> > > > >
> > > > > Frank
> > > > >
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "gmotichka" <gmotichka@h...>
> > > > > To: <ukha_xpl@xxxxxxx>
> > > > > Sent: Sunday, December 05, 2004 5:20 AM
> > > > > Subject: [ukha_xpl] HV Macro runs multiple times
> > > > >
> > > > >
> > > > > >
> > > > > >
> > > > > > I am getting very close on this working. I
now have it
where
> > the
> > > > x10
> > > > > > signal is recognized by the W800 and then
triggers the
macro
> > in
> > > > > > HomeVision.
> > > > > >
> > > > > > The problem is that it will execute the macro
multiple
> > times --
> > > > > > anywhere from 3 to 6 times consecutively. I
can see the
> > multiple
> > > > > > commands going to HV. I tried to add a 'macro
disable"
> > command in
> > > > > > the macro, but that did not help. Neither did
adjusting
the
> > > > ddespeed
> > > > > > or lastsent options in the configuration.
> > > > > >
> > > > > > Further suggestions would be welcomed.
> > > > > >
> > > > > > Thanks
> > > > > > George
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > xPL Links: http://www.xplproject.org.uk
http://www.xplhal.com
> > > > > http://www.xpl.myby.co.uk
> > > > > > To Post a Message: ukha_xpl@xxxxxxx
> > > > > > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > > > > > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> > > > > > Yahoo! Groups Links
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> > > http://www.xpl.myby.co.uk
> > > > To Post a Message: ukha_xpl@xxxxxxx
> > > > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > > > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> >
> >
> >
> >
> >
> >
> > xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> http://www.xpl.myby.co.uk
> > To Post a Message: ukha_xpl@xxxxxxx
> > To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> > To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >