The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: RE: Inc / Dec a Global


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

RE: X10 Schema and Preset Dim


  • Subject: RE: X10 Schema and Preset Dim
  • From: "Eric Vickery" <ericvic@xxxxxxxxxxx>
  • Date: Tue, 13 Dec 2005 13:01:24 -0600

Tom,

There must always be a level with a preset dim. When X-10 created the
Preset Dim command they wanted 32 levels and since they were going to
put the level in the house code portion of the x-10 transmission, which
can only deal with 1 to 16, they had to break Preset Dim into two
commands. That is how there is Preset Dim 1 and Preset Dim 2. Each
Preset Dim takes a level of 1 to 16 (technically 0 to 15) and with
Preset Dim 2 that level translates into 17 to 32.

I hope my explanation wasn't too confusing.

Eric

-----Original Message-----
From: ukha_xpl@xxxxxxx [mailto:ukha_xpl@xxxxxxx] On
Behalf Of Tom Van den Panhuyzen
Sent: Tuesday, December 13, 2005 4:45 AM
To: ukha_xpl@xxxxxxx
Subject: Re: [ukha_xpl] X10 Schema and Preset Dim


I suppose you would normally put that in the "level" field ?
I.e.:
command=predim1
device=A1,B7,G2
level=10

The medusa component ignores the level field for predim1 and predim2.
If you (or somebody else) acknowledge that a "predim" command is
always
used in combination with a "level" then I will add that to the
code.
(Minor change)

Tom


On 12/13/05, Eric Vickery <ericvic@xxxxxxx> wrote:
> For anyone that is using the X10 schema and PREDIM1 or PREDIM2 where
> are you putting the dim level?
>
> Eric
>
>
> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> http://www.xpl.myby.co.uk To
Post a Message: ukha_xpl@xxxxxxx
> To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
>
>
> ________________________________
> YAHOO! GROUPS LINKS
>
>  Visit your group "ukha_xpl" on the web.
>
>  To unsubscribe from this group, send an email to:
> ukha_xpl-unsubscribe@xxxxxxx
>
>  Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

> To unsubscribe from this group, send an email to:
> ukha_xpl-unsubscribe@xxxxxxx
>
>  Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
> ________________________________
>



xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
http://www.xpl.myby.co.uk To Post
a Message: ukha_xpl@xxxxxxx To
Subscribe:  ukha_xpl-subscribe@xxxxxxx
To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx

xPL Main Index | xPL Thread Index | xPL Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.