The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024

Latest message you have seen: Re: Email Test & Introduction


[Message Prev][Message Next][Thread Prev][Thread Next][Message Index][Thread Index]

Re: Quick schema queries



Hi Mal

> Not sure about the first part, but you are correct in thinking that
> messages are all lower case.

Has the specs changed ???.....my copy is dated 10/12/2003

Frank



----- Original Message -----
From: "Mal Lansell" <mal@xxxxxxx>
To: <ukha_xpl@xxxxxxx>
Sent: Saturday, November 26, 2005 9:47 AM
Subject: Re: [ukha_xpl] Quick schema queries


> Not sure about the first part, but you are correct in thinking that
> messages are all lower case.  My own SDK forces message elements to
> lower case before doing anything with them, so it can receive mixed
case
> messages just fine.
>
> Mal
>
>
> Mark Hindess wrote:
>
>>
>> Are x10.basic messages permitted to send the
"ALL_UNITS_ON" command?  It
>> is missing from the list of valid commands (both on the old site
and on
>> the wiki).  I was about to add it when I worried that perhaps it
was
>> intentional.  'ALL_LIGHTS_OFF' was in the list twice - I've
corrected
>> this on the wiki copy only.
>>
>> I went to read the osd.basic schema on the wiki and it hadn't been
>> copied over yet so I took the liberty of doing it.
>>
>> One thing that did cross my mind as I copied it.  Everything is in
upper
>> case, but Ian mentioned in passing a while back that:
>>
>>   name section (and indeed all sturctural elements of the message)
must
>>   be lowercase
>>
>> I left the case unchanged, but I guess these should really be
converted
>> to lowercase to avoid confusion?  (And converting the schemas when
they
>> are copied would be reasonably efficient time to do it.)
>>
>> I'll happily update osd.basic depending on the answer to this
question,
>> but I'm not volunteering to do them all. ;-)
>>
>> Also, would I be correct in thinking that values from predefined
sets
>> of constants - such as the X10 command values or 'write', 'clear',
etc
>> commands in the osd.basic schema - should also be lower case now?
>>
>> Obviously, I'm thinking sending here and being flexible about
receiving
>> upper/mixed case.
>>
>> Regards,
>> Mark.
>>
>>
>>
>>
>> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
>> http://www.xpl.myby.co.uk
>> To Post a Message: ukha_xpl@xxxxxxx
>> To Subscribe:  ukha_xpl-subscribe@xxxxxxx
>> To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
>>
>>
>>
>> SPONSORED LINKS
>> Protocol analyzer
>> <http://groups.yahoo.com/gads?t=ms&k=Protocol+analyzer&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=QulmGKu5OpHgigyaWFXqqA>
>> Protocol converter
>> <http://groups.yahoo.com/gads?t=ms&k=Protocol+converter&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=_Gav_2JNLbgwjsCn8RqM-w>
>> Sip protocol
>> <http://groups.yahoo.com/gads?t=ms&k=Sip+protocol&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=d2G6YVkW-P5WBFmpuWQ3Zw>
>>
>> Tcp
>> <http://groups.yahoo.com/gads?t=ms&k=Tcp&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=9xqmZjMntiOfVEPLIpwKUg>
>> Protocol analysis
>> <http://groups.yahoo.com/gads?t=ms&k=Protocol+analysis&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=j5RxaJ5TSW2NTgWhIna4qQ>
>> Protocol
>> <http://groups.yahoo.com/gads?t=ms&k=Protocol&w1=Protocol+analyzer&w2=Protocol+converter&w3=Sip+protocol&w4=Tcp&w5=Protocol+analysis&w6=Protocol&c=6&s=111&.sig=OPnkI6GadMASTgKewyeqDQ>
>>
>>
>>
>>
------------------------------------------------------------------------
>> YAHOO! GROUPS LINKS
>>
>>     *  Visit your group "ukha_xpl
>>       <http://groups.yahoo.com/group/ukha_xpl>"
on the web.
>>
>>     *  To unsubscribe from this group, send an email to:
>>        ukha_xpl-unsubscribe@xxxxxxx
>>       <mailto:ukha_xpl-unsubscribe@xxxxxxx?subject=Unsubscribe>
>>
>>     *  Your use of Yahoo! Groups is subject to the Yahoo! Terms of
>>       Service <http://docs.yahoo.com/info/terms/>.
>>
>>
>>
------------------------------------------------------------------------
>>
>
>
>
>
> xPL Links: http://www.xplproject.org.uk http://www.xplhal.com
> http://www.xpl.myby.co.uk
> To Post a Message: ukha_xpl@xxxxxxx
> To Subscribe:  ukha_xpl-subscribe@xxxxxxx
> To Unsubscribe:  ukha_xpl-unsubscribe@xxxxxxx
> Yahoo! Groups Links
>
>
>
>
>
>




xPL Main Index | xPL Thread Index | xPL Home | Archives Home

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.